ONE CONDUCTOR

10 Amp  (Model 110)

10 Amp  (Model 110-T)
250 Amp  (Model 1250)
500 Amp  (Model 1500)
TWO CONDUCTOR
4 Amp  (Model 205)
30 Amp, 250V (Model 230)
30 Amp, 500V (Model 235)
15 Amp, 2,000V (Model 215-2K)
THREE CONDUCTOR
4 Amp  (Model 305)
4 & 30 Amp (Model 331)
30 Amp, 250V (Model 330)
30 Amp, 500V (Model 335)
FOUR CONDUCTOR
4 & 30 Amp (Model 430)
30 Amp, 500V (Model 435)
100 Amp, 500V (Model 4100)
SIX CONDUCTOR
4 & 30 Amp  (Model 630)
EIGHT CONDUCTOR
4 & 30 Amp  (Model 830)


 

   
Model
215-2K

Two Conductors,
2@15amps & 2,000V

 


Disconnects included (4 lg.)
Boot Kit available
Available with stainless steel
  ball bearing (215-2KSS)
 
Mercotac model 215-2K series is ideal for high-voltage, two-wire applications such as ultrasonic welding.
Model No. Terminals Voltage
AC/DC
Amp
Rating
@2000VAC
Max.
Freq.
MHz
Contact
Resistance
Max.
RPM
Temp
Max. F (C) /
 Min. F (C)
Rotation
Torque (gm-cm)
Circuit
Separation
215-2K 2 0-2,000 15 100

<1m

1200 140 (60) /-20(-29) 400

>50M

215-2KSS 2 0-2,000 15 100

<1m

1200 140 (60) /-20(-29) 400

>50M

"SS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments)

Model 215-2K Accessories
57235
Boot Kit for dust or splash
protection IP51
552KA
Terminal 22 - 18 AWG
(qty. 4 included)
55253
Shrink Tube
(qty. 4 included)
 
Terminals for 16-14 AWG wires available (p/n 552KB).
Model 215-2K Standard Wire Connections

Model 215-2K Wire Connections With Optional Boot
  Model 215-2K Suggested Mounting Methods
Model 215-2K is typically mounted by either the black body or the white plastic bushing on either end using a set screw.  When mounting horizontally, mount the Mercotac so the body of the connector rotates.

Typical Body Mount Hole Dimensions

MODEL HOLE DIAMETER () * DEPTH
215-2K, et al 1.248"    (31.7) .80"    (20.3)

Typical Bushing Mount Hole Dimensions

215-2K, et al .748"    (19.0) .80"    (20.3)
*Inch  (mm) Tolerance    +.001" (+.025)
    -.000" (-.000)











Installation Notes:
  • the up arrow should not point below horizontal
  • do not solder to or bend connector tabs
  • avoid lateral forces and mechanical loads (overly stiff or tight wires)
  • do not rigid mount both ends of connector
  • limit mounting eccentricity (runout / wobble) to .005" (.13mm)
  • provide overload protection within the circuit
  • avoid vibration and bumping motions

Back Top Top

 


Mercotac, Inc.
6195 Corte del Cedro #100 Carlsbad, CA 92011
Telephone: (760) 431-7723  Fax: (760) 431-0905
Email: sales@mercotac.com Support: techsupport@mercotac.com